hubitat

IKEA Zigbee drivers

This document provides instructions on how to install and use custom drivers for IKEA Zigbee devices on Hubitat hub.

These drivers enable advanced features and functionalities for the following devices:

Lights:

• Dimmable Light
• White Spectrum Light
• Color White Spectrum Light
• RGB-Only Light

Remotes:

• Knycklan Water Valve Remote (E1841)
• Rodret Dimmer (E2201)
• Somrig Shortcut Button (E2213)
• Styrbar Remote Control N2 (E2002)
• Symfonisk Sound Remote Gen2 (E2123)
• Tradfri On/Off Switch (E1743)
• Tradfri Open/Close Remote (E1766)
• Tradfri Remote Control (E1810)
• Tradfri Shortcut Button (E1812)

Sensors:

• Badring Water Leakage Sensor (E2202)
• Parasoll Door/Window Sensor (E2013)
• Tradfri Motion Sensor (E1745)
• Vallhorn Motion Sensor (E2134)
• Vindstyrka Air Quality Sensor (E2112)

Outlets:

• Askvader On/Off Switch (E1836)
• Inspelning Smart Plug (E2206)
• Tradfri Control Outlet (E1603, E1706)
• Tretakt Smart Plug (E2204)

Appliances:

• Knycklan Water Valve Receiver (E1842)
• Starkvind Air Purifier (E2006)
• Tradfri Signal Repeater (E1746)

Devices from other vendors (not in HPM):

• Aqara Dual Relay Module T2 (DCM-K01)
• Gewiss 2-channel Contact Interface (GWA1501)
• Legrand Connected Outlet (741811)
• Philips Hue Wall Switch Module (RDM001)
• Philips Hue Dimmer Switch (RWL022)
• Schneider Wiser UFH (CCTFR6600)
• Swann One Key Fob (SWO-KEF1PA)
• Tuya Temperature and Humidity Sensor (TS0201)
• Xiaomi Mi Temperature and Humidity Monitor 2 (LYWSD03MMC)

Advanced features:

• Zigbee Bindings

Installation

There are two ways to install the drivers: using Hubitat Package Manager (HPM) or manually importing the driver code.

HPM Installation (Recommended)

HPM is an app that allows you to easily install and update custom drivers and apps on your Hubitat hub. To use HPM, you need to have it installed on your hub first.

Once you have HPM installed, follow these steps to install the IKEA Zigbee drivers:

1. In the Hubitat interface, go to Apps and select Hubitat Package Manager.
2. Select Install, then Search by Keywords.
3. Enter IKEA Zigbee drivers in the search box and click Next.
4. Select IKEA Zigbee drivers by Dan Danache and click Next.
5. Select the driver(s) you need from the dropdown list and follow the install instructions.

Manual Installation

If you don’t want to use HPM, you can also install the drivers manually by importing the driver code from GitHub. Follow these steps to do so:

1. In the Hubitat interface, go to Drivers Code.
2. Click New Driver in the top right, then click Import in the top right.
3. Search below for your device, look for the Manual install file property and enter it in the URL field.
4. Click Import, then click OK and the code should load in the editor.
5. Click Save in the top right.

More info about installing custom drivers is available in the Official Documentation.

Lights

Below you can find the details of each lighting device, including the features and pairing instructions.

Dimmable Light

These products come equipped with the following features:

• Wireless Dimming: Provides the flexibility to adjust the brightness level from a minimal 0% to a maximum 100%, catering to your specific lighting needs.

Also includes the 10W and 30W LED drivers.

Parameter	Details
Icon
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_DIM-Light.groovy
Since version	5.0.0

Features

• Command Controls: Includes “On”, “Off”, “Toggle”, and “On with Timed Off” commands.
• Power Outage Configuration: Configures the state after a power outage (options include “Power On”, “Power Off”, and “Restore previous state”).
• Brightness Control: Allows setting of brightness level, starting/stopping brightness level change, and stepping brightness level up/down.
• Brightness Configuration: Configures brightness level when turned on (options include “Always the same fixed value”, and “Restore last level”).
• Pre-staging: Allows setting of brightness level when the lights are off (and they stay off). When the lights are turned on, they will start at the specified level.
• Health Status: Indicates whether the device is online or offline.
• Device State Refresh: Refreshes the device state on demand for real-time status updates.
• Zigbee Group Membership: The device can be a member of Zigbee groups. This allows for efficient management of multiple devices.

Tested devices

Type	Name
LED2103G5	Tradfri Bulb E27 WW Globe 806lm
LED2104R3	Tradfri Bulb GU10 WW 345lm
LED1623G12	Tradfri Bulb E27 Opal 1000lm
LED1649C5E14EU	Tradfri Bulb E14 W op/ch 400lm
LED1934G3	Tradfri Bulb E27 WW Clear 250lm
LED1837R5	Tradfri Bulb GU10 WW 400lm
LED1842G3	Tradfri Bulb E27 WW Clear 250lm
LED1836G9	Tradfri Bulb E27 WW 806lm
10EU-IL-1	Tradfri LED Driver (10W)
30-IL44-1	Silverglans LED Driver (30W)
30EU-IL-2	Tradfri LED Driver (30W)

Pairing Instructions

1. If the device is already powered on, power it off for 20 seconds (power-cycle) before each pairing attempt.
2. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
3. Put the light in pairing mode (see video).
4. Return to the pairing page, provide a name for your device, and assign it to a room.
5. You’re all set! Enjoy using your Dimmable Light.

White Spectrum Light

These products have the following features: These products come equipped with the following features:

• Wireless Dimming: Provides the flexibility to adjust the brightness level from a minimal 0% to a maximum 100%, catering to your specific lighting needs.

• Adjustable White Tones: Offers the ability to modify the color temperature within a range of 2200 Kelvin (which emits a warm glow) to 4000 Kelvin (which produces a cool white light), allowing you to create the perfect ambiance.

Parameter	Details
Icon
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_WS-Light.groovy
Since version	5.0.0

Features

• Command Controls: Includes “On”, “Off”, “Toggle”, and “On with Timed Off” commands.
• Power Outage Configuration: Configures the state after a power outage (options include “Power On”, “Power Off”, and “Restore previous state”).
• Brightness Control: Allows setting of brightness level, starting/stopping brightness level change, and stepping brightness level up/down.
• Color Temperature (CT) Control: Enables setting of color temperature, starting/stopping color temperature change, and stepping color temperature up/down.
• Brightness Configuration: Configures brightness level when turned on (options include “Always the same fixed value”, and “Restore last level”).
• Pre-staging: Allows setting of brightness level and color temperature when the lights are off (and they stay off). When the lights are turned on, they will start at the specified level/temperature.
• Health Status: Indicates whether the device is online or offline.
• Device State Refresh: Refreshes the device state on demand for real-time status updates.
• Zigbee Group Membership: The device can be a member of Zigbee groups. This allows for efficient management of multiple devices.

Known Issues

• Color Temperature and Brightness Level: These can be set together if the “Transition time” is 0 (or left blank in the UI); if a transition time is specified, only the color temperature is applied.

Tested devices

Type	Name
LED2106R3	Tradfri Bulb GU10 WS 345lm
LED2101G4	Tradfri Bulb E14 WS Globe 470lm
LED1949C5	Tradfri Bulb E14 WS Candle Opal 470lm
LED2002G5	Tradfri Bulb E14 WS Globe Opal 470lm
LED2003G10	Tradfri Bulb E27 WS Globe Opal 1055lm
LED2005R5	Tradfri Bulb GU10 WS 345lm
LED2201G8	Tradfri Bulb E27 WS Globe 1055lm
LED1835C6	Tradfri Bulb E14 WS 470lm

Pairing Instructions

1. If the device is already powered on, power it off for 20 seconds (power-cycle) before each pairing attempt.
2. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
3. Put the light in pairing mode (see video).
4. Return to the pairing page, provide a name for your device, and assign it to a room.
5. You’re all set! Enjoy using your White Spectrum Light.

Color White Spectrum Light

These products come equipped with the following features:

• Wireless Dimming: Provides the flexibility to adjust the brightness level from a minimal 0% to a maximum 100%, catering to your specific lighting needs.

• Adjustable White Tones: Offers the ability to modify the color temperature within a range of 2200 Kelvin (which emits a warm glow) to 4000 Kelvin (which produces a cool white light), allowing you to create the perfect ambiance.

• Adjustable Color: Grants comprehensive control over the light color by manipulating the hue, saturation, and level (HSL), enabling you to personalize your lighting experience.

Parameter	Details
Icon
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_CWS-Light.groovy
Since version	5.0.0

Features

• Command Controls: Includes “On”, “Off”, “Toggle”, and “On with Timed Off” commands.
• Power Outage Configuration: Configures the state after a power outage (options include “Power On”, “Power Off”, and “Restore previous state”).
• Brightness Control: Allows setting of brightness level, starting/stopping brightness level change, and stepping brightness level up/down.
• Color Temperature (CT) Control: Enables setting of color temperature, starting/stopping color temperature change, and stepping color temperature up/down.
• Color (RGB) Control: Provides options to set color hue and/or saturation, and display color name and color mode.
• Color Loop: Initiates cycling of the color hue until stopped.
• Brightness Configuration: Configures brightness level when turned on (options include “Always the same fixed value”, and “Restore last level”).
• Pre-staging: Allows setting of brightness level, color temperature, and color when the lights are off (and they stay off). When the lights are turned on, they will start at the specified level/temperature/color.
• Health Status: Indicates whether the device is online or offline.
• Device State Refresh: Refreshes the device state on demand for real-time status updates.
• Zigbee Group Membership: The device can be a member of Zigbee groups. This allows for efficient management of multiple devices.

Known Issues

• Color Temperature and Brightness Level: These can be set together if the “Transition time” is 0 (or left blank in the UI); if a transition time is specified, only the color temperature is applied.

Tested devices

Type	Name
LED1924G9	Tradfri Bulb E27 CWS 806lm
LED1923R5	Tradfri Bulb GU10 CWS 345lm
LED1925G6	Tradfri Bulb E14 CWS 470lm
L2112	Ormanas LED Strip
LED2110R3	Tradfri Bulb GU10 CWS 345lm
LED2111G6	Tradfri Bulb E14 CWS Globe 806lm

Pairing Instructions

1. If the device is already powered on, power it off for 20 seconds (power-cycle) before each pairing attempt.
2. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
3. Put the light in pairing mode (see video).
4. Return to the pairing page, provide a name for your device, and assign it to a room.
5. You’re all set! Enjoy using your Color White Spectrum Light.

RGB-Only Light

These products come equipped with the following features:

• Wireless Dimming: Provides the flexibility to adjust the brightness level from a minimal 0% to a maximum 100%, catering to your specific lighting needs.

• Adjustable Color: Grants comprehensive control over the light color by manipulating the hue, saturation, and level (HSL), enabling you to personalize your lighting experience.

Bulbs of this type lack native support for color temperature control. Their hardware is exclusively equipped with red, green, and blue LEDs, and does not include white light LEDs. As a result, they are unable to natively produce variations in light temperature.

Parameter	Details
Icon
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_RGBO-Light.groovy
Since version	5.0.0

Features

• Command Controls: Includes “On”, “Off”, “Toggle”, and “On with Timed Off” commands.
• Power Outage Configuration: Configures the state after a power outage (options include “Power On”, “Power Off”, and “Restore previous state”).
• Brightness Control: Allows setting of brightness level, starting/stopping brightness level change, and stepping brightness level up/down.
• Color (RGB) Control: Provides options to set color hue and/or saturation, and display color name and color mode.
• Brightness Configuration: Configures brightness level when turned on (options include “Always the same fixed value”, and “Restore last level”).
• Pre-staging: Allows setting of brightness level and color when the lights are off (and they stay off). When the lights are turned on, they will start at the specified level/color.
• Health Status: Indicates whether the device is online or offline.
• Device State Refresh: Refreshes the device state on demand for real-time status updates.
• Zigbee Group Membership: The device can be a member of Zigbee groups. This allows for efficient management of multiple devices.

Tested devices

Type	Name
LED1624G9E27EU	Tradfri Bulb E27 CWS Opal 600lm
LED1624G9E14EU	Tradfri Bulb E14 CWS Opal 600lm

Pairing Instructions

1. If the device is already powered on, power it off for 20 seconds (power-cycle) before each pairing attempt.
2. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
3. Put the light in pairing mode (see video).
4. Return to the pairing page, provide a name for your device, and assign it to a room.
5. You’re all set! Enjoy using your RGB-Only Light.

Remotes

Below you can find the details of each remote device, including the features and pairing instructions.

Knycklan Water Valve Remote (E1841)

Parameter	Details
Product Image
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_E1841.groovy
Tested firmwares	2.3.019
Since version	5.0.0

Features

• Button Events: Supports “Push”, “Hold”, and “Release” events for both buttons.
• Battery Report: Provides a percentage-based report on the current battery level.
• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.
• Zigbee Device Control: Enables direct control of On/Off and Brightness settings for Zigbee devices.

Pairing Instructions

1. Using a small screwdriver, open the battery compartiment and you should see the small pair button (🔗).
2. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
3. Important: Move closer to your Hubitat hub and press the pair button in the battery compartment four times within five seconds.
4. Important: Immediately after the device LED starts blinking red, position the device as close as possible to your Hubitat hub for at least 30 seconds (wait until the LED stops blinking and turns off).
5. Return to the pairing page, provide a name for your device, and assign it to a room.
6. Close the device battery compartiment.
7. You’re all set! Enjoy using your Knycklan Water Valve Remote.

Rodret Dimmer (E2201)

Parameter	Details
Product Image
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_E2201.groovy
Tested firmwares	1.0.47｜1.0.57
Since version	2.0.0

Features

• Button Events: Supports “Push”, “Hold”, and “Release” events for both buttons.
• Battery Report: Provides a percentage-based report on the current battery level.
• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.
• Direct Zigbee Device Control: Enables direct control of On/Off and Brightness settings for Zigbee devices.
• Direct Zigbee Group Control: Enables direct control of On/Off and Brightness settings for Zigbee groups. This allows for efficient management of multiple devices.

Pairing Instructions

1. Open the battery compartiment and you should see the small pair button (🔗).
2. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
3. Important: Move closer to your Hubitat hub and press the pair button in the battery compartment four times within five seconds.
4. Important: Immediately after the device LED starts blinking red, position the device as close as possible to your Hubitat hub for at least 30 seconds (wait until the LED stops blinking and turns off).
5. Return to the pairing page, provide a name for your device, and assign it to a room.
6. Close the device battery compartiment.
7. You’re all set! Enjoy using your Rodret Dimmer.

Somrig Shortcut Button (E2213)

Parameter	Details
Product Image
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_E2213.groovy
Tested firmwares	1.0.20｜1.0.21
Since version	3.6.0

Features

• Button Events: Supports “Push”, “Double-Tap”, “Hold”, and “Release” events for both buttons.
• Battery Report: Provides a percentage-based report on the current battery level.
• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.
• Direct Zigbee Device Control: Enables direct control of On/Off and Brightness settings for Zigbee devices.
• Direct Zigbee Group Control: Enables direct control of On/Off and Brightness settings for Zigbee groups. This allows for efficient management of multiple devices.

Pairing Instructions

1. Using a small screwdriver, open the battery compartiment and you should see the small pair button (🔗).
2. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
3. Important: Move closer to your Hubitat hub and press the pair button in the battery compartment four times within five seconds.
4. Important: Immediately after the device LED starts blinking red, position the device as close as possible to your Hubitat hub for at least 30 seconds (wait until the LED stops blinking and turns off).
5. Return to the pairing page, provide a name for your device, and assign it to a room.
6. Close the device battery compartiment.
7. You’re all set! Enjoy using your Somrig Shortcut Button.

Styrbar Remote Control N2 (E2002)

Parameter	Details
Product Image
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_E2002.groovy
Tested firmwares	1.0.024｜2.4.5｜2.4.11
Since version	2.0.0

Features

• Button Events: Supports “Push” events for all buttons, “Hold” and “Release” events for Button 1 (🔆) and Button 2 (🔅).
• Battery Report: Provides a percentage-based report on the current battery level.
• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.
• Zigbee Device Control: Enables direct control of On/Off, Brightness, and Scenes for Zigbee devices.

Known Issues

• The Hold / Release events don’t work correctly on the Next and Prev buttons.
• Old firmware versions (below 2.4.5) send multiple events per button push. You can update the device to the latest version using Hubitat.

Pairing Instructions

1. Using a small screwdriver, open the battery compartiment and you should see the small pair button (🔗).
2. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
3. Important: Move closer to your Hubitat hub and press the pair button in the battery compartment four times within five seconds.
4. Important: Immediately after the device LED starts blinking red, position the device as close as possible to your Hubitat hub for at least 30 seconds (wait until the LED stops blinking and turns off).
5. Return to the pairing page, provide a name for your device, and assign it to a room.
6. Close the device battery compartiment.
7. You’re all set! Enjoy using your Styrbar Remote Control.

Symfonisk Sound Remote Gen2 (E2123)

Parameter	Details
Product Image
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_E2123.groovy
Tested firmwares	1.0.012｜1.0.35
Since version	1.0.0

Features

• Button Events: Supports “Push” events for all buttons, “Hold” events for Button 2 (Plus), Button 3 (Minus), Button 6 (•), and Button 7 (••), “Release” and “Double-Tap” events for Button 6 (•) and Button 7 (••).
• Battery Report: Provides a percentage-based report on the current battery level.
• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.
• Zigbee Device Control: Enables direct control of On/Off settings for Zigbee devices.
• Zigbee Group Control: Enables direct control of On/Off settings for Zigbee groups. This allows for efficient management of multiple devices.

Known Issues

• Old firmware versions (below 1.0.35) does not send the release event for Button 6 (•) and Button 7 (••)

Pairing Instructions

1. Open the battery compartiment and you should see the small pair button (🔗).
2. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
3. Important: Move closer to your Hubitat hub and press the pair button in the battery compartment four times within five seconds.
4. Important: Immediately after the device LED starts blinking red, keep the device as close as you can against your Hubitat hub until the LED stops blinking and turns off.
5. Return to the pairing page, provide a name for your device, and assign it to a room.
6. Close the device battery compartiment.
7. You’re all set! Enjoy using your Symfonisk Sound Remote.

Tradfri On/Off Switch (E1743)

Parameter	Details
Product Image
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_E1743.groovy
Tested firmwares	2.2.010｜24.4.6
Since version	2.0.0

Features

• Button Events: Supports “Push”, “Hold”, and “Release” events for both buttons.
• Battery Report: Provides a percentage-based report on the current battery level.
• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.
• Zigbee Device Control: Enables direct control of On/Off and Brightness settings for Zigbee devices.

Pairing Instructions

1. Using a small screwdriver, open the battery compartiment and you should see the small pair button (🔗).
2. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
3. Important: Move closer to your Hubitat hub and press the pair button in the battery compartment four times within five seconds.
4. Important: Immediately after the device LED starts blinking red, position the device as close as possible to your Hubitat hub for at least 30 seconds (wait until the LED stops blinking and turns off).
5. Return to the pairing page, provide a name for your device, and assign it to a room.
6. Close the device battery compartiment.
7. You’re all set! Enjoy using your Tradfri On/Off Switch.

Tradfri Open/Close Remote (E1766)

Parameter	Details
Product Image
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_E1766.groovy
Tested firmwares	24.4.6
Since version	3.3.0

Features

• Button Events: Supports “Push” and “Release” events for both buttons.
• Battery Report: Provides a percentage-based report on the current battery level.
• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.
• Zigbee Device Control: Enables direct control of “Window Covering” for Zigbee devices.

Pairing Instructions

1. Using a small screwdriver, open the battery compartiment and you should see the small pair button (🔗).
2. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
3. Important: Move closer to your Hubitat hub and press the pair button in the battery compartment four times within five seconds.
4. Important: Immediately after the device LED starts blinking red, position the device as close as possible to your Hubitat hub for at least 30 seconds (wait until the LED stops blinking and turns off).
5. Return to the pairing page, provide a name for your device, and assign it to a room.
6. Close the device battery compartiment.
7. You’re all set! Enjoy using your Tradfri Open/Close Remote.

Tradfri Remote Control (E1810)

Parameter	Details
Product Image
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_E1810.groovy
Tested firmwares	24.4.5
Since version	1.1.0

Features

• Button Events: Supports “Push” events for all buttons, “Hold” and “Release” events for Button 2 (🔆), Button 3 (🔅), Button 4 (Next), and Button 5 (Prev).
• Battery Report: Provides a percentage-based report on the current battery level.
• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.
• Zigbee Device Control: Enables direct control of On/Off, Brightness, and Scenes for Zigbee devices.

Known Issues

• Old firmware versions suppport binding to groups only and this functionality is not supported by the Hubitat hub. You can update the device to the latest version using Hubitat.

Pairing Instructions

1. Open the battery compartiment and you should see the small pair button (🔗).
2. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
3. Important: Move closer to your Hubitat hub and press the pair button in the battery compartment four times within five seconds.
4. Important: Immediately after the device LED starts blinking red, position the device as close as possible to your Hubitat hub for at least 30 seconds (wait until the LED stops blinking and turns off).
5. Return to the pairing page, provide a name for your device, and assign it to a room.
6. Close the device battery compartiment.
7. You’re all set! Enjoy using your Tradfri Remote Control.

Tradfri Shortcut Button (E1812)

Parameter	Details
Product Image
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_E1812.groovy
Tested firmwares	2.3.015｜24.4.6
Since version	2.0.0

Features

• Button Events: Supports “Push”, “Double-Tap” (only on firmware 24.4.6 and above), “Hold”, and “Release” events.
• Battery Report: Provides a percentage-based report on the current battery level.
• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.
• Direct Zigbee Device Control: Enables direct control of On/Off and Brightness settings for Zigbee devices.

Pairing Instructions

1. Using a small screwdriver, open the battery compartiment and you should see the small pair button (🔗).
2. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
3. Important: Move closer to your Hubitat hub and press the pair button in the battery compartment four times within five seconds; the red LED light can be seen from the back / battery side.
4. Important: Immediately after the device LED starts blinking red, position the device as close as possible to your Hubitat hub for at least 30 seconds (wait until the LED stops blinking and turns off).
5. Return to the pairing page, provide a name for your device, and assign it to a room.
6. Close the device battery compartiment.
7. You’re all set! Enjoy using your Tradfri Shortcut Button.

Sensors

Below you can find the details of each sensor device, including the features and pairing instructions.

Badring Water Leakage Sensor (E2202)

Parameter	Details
Product Image
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_E2202.groovy
Tested firmwares	1.0.7
Since version	3.9.0

Features

• Water Detection: Identifies the state of water presence as either “wet” or “dry”.
• Battery Report: Provides a percentage-based report on the current battery level.
• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.

Pairing Instructions

1. Open the battery compartiment and you should see the small pair button (🔗).
2. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
3. Important: Move closer to your Hubitat hub and press the pair button in the battery compartment four times within five seconds.
4. Important: Immediately after the device LED starts blinking red, position the device as close as possible to your Hubitat hub for at least 30 seconds (wait until the LED stops blinking and turns off).
5. Return to the pairing page, provide a name for your device, and assign it to a room.
6. Close the device battery compartiment.
7. You’re all set! Enjoy using your Badring Water Leakage Sensor.

Parasoll Door/Window Sensor (E2013)

Parameter	Details
Product Image
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_E2013.groovy
Tested firmwares	1.0.19
Since version	3.6.0

Features

• Contact Status: Identifies the state of contact sensor as either “open” or “close”.
• Battery Report: Provides a percentage-based report on the current battery level.
• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.
• Direct Zigbee Device Control: Enables direct control of On/Off and Brightness settings for Zigbee devices.
• Direct Zigbee Group Control: Enables direct control of On/Off and Brightness settings for Zigbee groups. This allows for efficient management of multiple devices.

Pairing Instructions

1. Remove device from its position using a small screwdriver and, on the back, you should see the small pair button (🔗).
2. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
3. Important: Move closer to your Hubitat hub and press the pair button in the battery compartment four times within five seconds.
4. Important: Immediately after the device LED starts blinking red, position the device as close as possible to your Hubitat hub for at least 30 seconds (wait until the LED stops blinking and turns off).
5. Return to the pairing page, provide a name for your device, and assign it to a room.
6. Place the device back to its position by gently pressing it until you hear it clicking in place.
7. You’re all set! Enjoy using your Parasoll Door/Window Sensor.

Tradfri Motion Sensor (E1745)

Parameter	Details
Product Image
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_E1745.groovy
Tested firmwares	24.4.5
Since version	2.3.0

Features

This device offers a range of features:

• Motion Detection: Identifies motion as either “active” or “inactive”, with a cooldown period of 50 seconds.
• Illumination Detection: Detects illumination levels as either “dim” or “bright”.
• Dark Motion Detection: Provides an option to detect motion only when the illumination is dark.
• Battery Report: Provides a percentage-based report on the current battery level.
• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.

Known Issues

• Firmware Compatibility: Older firmware versions (below 24.4.5) support binding to groups only. This functionality is not supported by the Hubitat hub. Users can update the device to the latest version using Hubitat.
• Illumination Reporting: Illumination levels are reported only when motion is detected.

Pairing Instructions

1. Open the back compartiment and you should see the small pair button (🔗).
2. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
3. Important: Move closer to your Hubitat hub and press the pair button in the battery compartment four times within five seconds.
4. Important: Immediately after the device LED starts blinking red, position the device as close as possible to your Hubitat hub for at least 30 seconds (wait until the LED stops blinking and turns off).
5. Return to the pairing page, provide a name for your device, and assign it to a room.
6. Close the device battery compartiment.
7. You’re all set! Enjoy using your Tradfri Motion Sensor.

Vallhorn Motion Sensor (E2134)

Parameter	Details
Product Image
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_E2134.groovy
Tested firmwares	1.0.57｜1.0.64
Since version	3.6.0

Features

• Motion Detection: Identifies motion as either “active” or “inactive”, with a cooldown period of 20 seconds.
• Illumination Lux Reporting: Provides reports on the level of illumination, measured in lux. Reports are generated every 5 minutes.
• Battery Report: Provides a percentage-based report on the current battery level.
• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.

Known Issues

• Max reported illuminance is 1364 lux; more than enough for indoor usage

Pairing Instructions

1. Remove device from its position using a small screwdriver and, on the back, you should see the small pair button (🔗).
2. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
3. Important: Move closer to your Hubitat hub and press the pair button in the battery compartment four times within five seconds.
4. Important: Immediately after the device LED starts blinking red, keep the device as close as you can against your Hubitat hub for **at least 30 seconds** (after the front light stops blinking and turns off).
5. Return to the pairing page, provide a name for your device, and assign it to a room.
6. Place the device back to its position by gently pressing it until you hear it clicking in place.
7. You’re all set! Enjoy using your Vallhorn Motion Sensor.

Vindstyrka Air Quality Sensor (E2112)

Parameter	Details
Product Image
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_E2112.groovy
Tested firmwares	1.0.10｜1.0.11
Since version	3.8.0

Features

• Particulate Matter Sensor: Provides data for particulate matter less than 2.5 microns (PM 2.5).
• US AQI Score Calculation: Calculates the US Air Quality Index (AQI) score based on the PM 2.5 value.
• Sensirion VOC Index: Provides a Sensirion Volatile Organic Compounds (VOC) Index that ranges from 1 to 500, offering a quantified measure of the VOCs present in the surrounding air.
• Temperature and Humidity Measurements: Provide standard measurements of the current temperature and the amount of moisture in the air.
• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.
• Device State Refresh: Refreshes the device state on demand for real-time status updates.

Pairing Instructions

1. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
2. Click the pair button (🔗), located on the top of the device, 4 times in 5 seconds.
3. Return to the pairing page, provide a name for your device, and assign it to a room.
4. You’re all set! Enjoy using your Vindstyrka Air Quality Sensor.

Outlets

Below you can find the details of each outlet device, including the features and pairing instructions.

Askvader On/Off Switch (E1836)

Parameter	Details
Product Image
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_E1836.groovy
Tested firmwares	1.0.002
Since version	3.1.0

Features

• Command Controls: Includes “On”, “Off”, “Toggle”, and “On with Timed Off” commands.
• Power Outage Configuration: Configures the state after a power outage (options include “Power On”, “Power Off”, and “Restore previous state”).
• Health Status: Indicates whether the device is online or offline.
• Device State Refresh: Refreshes the device state on demand for real-time status updates.
• Zigbee Group Membership: The device can be a member of Zigbee groups. This allows for efficient management of multiple devices.

Pairing Instructions

1. Locate the small reset hole (located between the On/Off button and the LED light) and have a pin or pencil ready to fit the hole.
2. If the device is already plugged in, unplug it for 20 seconds (power-cycle) before each pairing attempt.
3. Plug the device back into an outlet.
4. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
5. Insert the pin into the reset hole and press it for at least 5 seconds; the LED light will start blinking upon release.
6. Return to the pairing page, provide a name for your device, and assign it to a room.
7. You’re all set! Enjoy using your Askvader On/Off Switch.

Inspelning Smart Plug (E2206)

Parameter	Details
Product Image
Variants	E2220 🇺🇸｜E2223 🇬🇧｜E2222 🇫🇷｜E2225 🇦🇺
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_E2206.groovy
Tested firmwares	2.4.45
Since version	5.1.0

Features

• Command Controls: Includes “On”, “Off”, “Toggle”, and “On with Timed Off” commands.
• Power Outage Configuration: Configures the state after a power outage (options include “Power On”, “Power Off”, and “Restore previous state”).
• Current Reporting: Reports the current (in Amperes).
• Voltage Reporting: Reports the volatage (in Volts).
• Power Reporting: Reports the power (in Watts).
• Energy Consumption Reporting: Reports the energy consumption (in kWh).
• Child Lock: Allows the enabling or disabling of the physical button on the device, providing an additional layer of safety.
• Dark Mode: Allows the LED indicator on the device to be turned off, ensuring total darkness when needed.
• Health Status: Indicates whether the device is online or offline.
• Device State Refresh: Refreshes the device state on demand for real-time status updates.
• Zigbee Group Membership: The device can be a member of Zigbee groups. This allows for efficient management of multiple devices.

Known Issues

• Voltage reporting is broken in old firmware versions (below 2.4.45). You can update the device firmware directly from Hubitat.

• By default, the Inspelning Smart Plug generates frequent updates when the connected device doesn’t maintain a constant power draw. These settings are suitable for phone chargers and small appliances. If you notice an excessive number of “info” entries in the Live logs, you can reduce the smart plug’s “sensitivity” using the dropdown menus in the “Preferences” section.

Pairing Instructions

1. Find the small reset button near on/off button and make sure you have a pointy object at hand.
2. If the device is already plugged in, unplug it for 20 seconds (power-cycle) before each pairing attempt.
3. Plug the device back into an outlet.
4. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
5. Push the small reset button on top of the smart plug with a pointy object for at least 5 seconds until the LED starts pulsating.
6. Return to the pairing page, provide a name for your device, and assign it to a room.
7. You’re all set! Enjoy using your Inspelning Smart Plug.

Tradfri Control Outlet (E1603, E1706)

Parameter	Details
Product Image
Variants	E1706 🇺🇸｜E1708 🇦🇺
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_E1603.groovy
Tested firmwares	2.0.0244｜2.3.089
Since version	2.0.0

Features

• Command Controls: Includes “On”, “Off”, “Toggle”, and “On with Timed Off” commands.
• Power Outage Configuration: Configures the state after a power outage (options include “Power On”, “Power Off”, and “Restore previous state”).
• Health Status: Indicates whether the device is online or offline.
• Device State Refresh: Refreshes the device state on demand for real-time status updates.
• Zigbee Group Membership: The device can be a member of Zigbee groups. This allows for efficient management of multiple devices.

Pairing Instructions

1. Find the small reset hole on the side of the device and make sure you have at hand a pin that can fit the reset hole (e.g.: a paper clip or SIM card eject pin).
2. If the device is already plugged in, unplug it for 20 seconds (power-cycle) before each pairing attempt.
3. Plug the device back into an outlet.
4. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
5. Insert the pin into the reset hole and press it for at least 5 seconds; upon release, the LED light will start blinking.
6. Return to the pairing page, provide a name for your device, and assign it to a room.
7. You’re all set! Enjoy using your Tradfri Control Outlet.

Tretakt Smart Plug (E2204)

Parameter	Details
Product Image
Variants	E2205 🇺🇸｜E2240 🇬🇧｜E2209 🇫🇷｜E2217 🇦🇺
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_E2204.groovy
Tested firmwares	2.4.4｜2.4.25
Since version	4.0.0

Features

• Command Controls: Includes “On”, “Off”, “Toggle”, and “On with Timed Off” commands.
• Power Outage Configuration: Configures the state after a power outage (options include “Power On”, “Power Off”, and “Restore previous state”).
• Child Lock: Allows the enabling or disabling of the physical button on the device, providing an additional layer of safety.
• Dark Mode: Allows the LED indicator on the device to be turned off, ensuring total darkness when needed.
• Health Status: Indicates whether the device is online or offline.
• Device State Refresh: Refreshes the device state on demand for real-time status updates.
• Zigbee Group Membership: The device can be a member of Zigbee groups. This allows for efficient management of multiple devices.

Pairing Instructions

1. Find the small reset button near on/off button and make sure you have a pointy object at hand.
2. If the device is already plugged in, unplug it for 20 seconds (power-cycle) before each pairing attempt.
3. Plug the device back into an outlet.
4. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
5. Push the small reset button on top of the smart plug with a pointy object for at least 5 seconds until the LED starts pulsating.
6. Return to the pairing page, provide a name for your device, and assign it to a room.
7. You’re all set! Enjoy using your Tretakt Smart Plug.

Appliances

Below you can find the details of each appliance device, including the features and pairing instructions.

Knycklan Water Valve Receiver (E1842)

Parameter	Details
Product Image
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_E1842.groovy
Tested firmwares	2.3.024
Since version	5.0.0

Features

• Command Controls: Includes “On”, “Off”, “Toggle”, and “On with Timed Off” commands.
• Power Outage Configuration: Configures the state after a power outage (options include “Power On”, “Power Off”, and “Restore previous state”).
• Health Status: Indicates whether the device is online or offline.
• Device State Refresh: Refreshes the device state on demand for real-time status updates.
• Zigbee Group Membership: The device can be a member of Zigbee groups. This allows for efficient management of multiple devices.

Pairing Instructions

1. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
2. Press and hold the On and Off buttons simultaneously for 5 seconds.
3. Return to the pairing page, provide a name for your device, and assign it to a room.
4. You’re all set! Enjoy using your Knycklan Water Valve Receiver.

Starkvind Air Purifier (E2006)

Parameter	Details
Product Image
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_E2006.groovy
Tested firmwares	1.0.033｜1.1.001
Since version	3.5.0

Features

• Command Controls: Includes “On”, “Off”, “Toggle”, and “Set/Cycle fan speed” commands.
• Particulate Matter Sensor: Provides data for particulate matter less than 2.5 microns (PM 2.5).
• US AQI Score Calculation: Calculates the US Air Quality Index (AQI) score based on the PM 2.5 value.
• Filter Information: Reports filter usage (%) and filter status (options include “normal” and “replace”).
• Configuration Options: Allows configuration of sensor report frequency, filter lifetime, and LED indicator status.
• Child Lock: Enables or disables physical controls on the device for safety.
• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.
• Device State Refresh: Refreshes the device state on demand for real-time status updates.

Pairing Instructions

1. If the device is already plugged in, unplug it for 20 seconds (power-cycle) before each pairing attempt.
2. Plug the device back into an outlet.
3. Open the round top lid and you should see the pair button (🔗) next to the filter reset button.
4. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
5. Press and hold the pair button for at least 5 seconds until the LED starts blinking.
6. Return to the pairing page, provide a name for your device, and assign it to a room.
7. Put back the lid and fix it in place.
8. You’re all set! Enjoy using your Starkvind Air Purifier.

Tradfri Signal Repeater (E1746)

Parameter	Details
Product Image
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Ikea_E1746.groovy
Tested firmwares	2.3.086
Since version	5.2.0

Features

• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.
• Device State Refresh: Refreshes the device state on demand for real-time status updates.

Attributes

• resets: A counter that is incremented each time the device resets. A reset is defined as any time the device restarts. This is not the same as a reset to factory defaults, which SHOULD clear this and all values
• macRxBcast: A counter that is incremented each time the MAC layer receives a broadcast.
• macTxBcast: A counter that is incremented each time the MAC layer transmits a broadcast.
• apsRxBcast: A counter that is incremented each time the APS layer receives a broadcast.
• apsTxBcast: A counter that is incremented each time the APS layer transmits a broadcast.
• nwkDropped: A counter that is incremented each time a message is dropped at the network layer because the APS frame counter was not higher than the last message seen from that source.
• memFailures: A counter that is incremented each time the stack failed to allocate a packet buffers. This doesn’t necessarily mean that the packet buffer count was 0 at the time, but that the number requested was greater than the number free.
• macRetries: A counter that is equal to the average number of MAC retries needed to send an APS message.
• lqi: This is the Link Quality Indicator for the last message received. There is no current agreed upon standard for calculating the LQI. For some implementations LQI is related directly to RSSI for others it is a function of the number of errors received over a fixed number of bytes in a given message. The one thing that has been agreed is that the Link Quality Indicator is a value between 0 and 255 where 0 indicates the worst possible link and 255 indicates the best possible link.
• rssi: This is the receive signal strength indication for the last message received.

Pairing Instructions

1. Find the small reset hole on the side of the device and make sure you have at hand a pin that can fit the reset hole (e.g.: a paper clip or SIM card eject pin).
2. If the device is already plugged in, unplug it for 20 seconds (power-cycle) before each pairing attempt.
3. Plug the device back into an outlet.
4. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
5. Insert the pin into the reset hole and press it for at least 5 seconds; upon release, the LED light will start blinking.
6. Return to the pairing page, provide a name for your device, and assign it to a room.
7. You’re all set! Enjoy using your Tradfri Signal Repeater.

Devices from other vendors

Below you can find the details of each device, including the features and pairing instructions.

Aqara Dual Relay Module T2 (DCM-K01)

Parameter	Details
Product Image
Product Link	Dual Relay Module T2
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Aqara_DCM-K01.groovy
Since version	4.0.0

Features

• Standard Operation Mode: In this mode, the switches S1/S2 control the relays L1/L2.
• Decoupled Operation Mode: In this mode, the switches S1/S2 only send “push” events.
• Switch Type Configuration: Allows the configuration of the switch type to be either latching, momentary, or disabled.
• Relay Type Configuration: Allows the configuration of the relay type to be either a wet contact, dry contact, or pulse mode. The pulse mode has a configurable pulse duration ranging from 200ms to 2000ms.
• Interlock Mode Configuration: Prevents both Relay L1 and Relay L2 from being On at the same time.
• Power Outage Configuration: Configures the state after a power outage (options include “Power On”, “Power Off”, and “Restore previous state”).
• Device Temperature Reporting: Reports the device’s temperature.
• Power Reporting: Reports the power (in Watts) of L1 + L2.
• Energy Consumption Reporting: Reports the energy consumption (in kWh) of L1 + L2.
• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.
• Device State Refresh: Refreshes the device state on demand for real-time status updates.

Pairing Instructions

1. If the device is already powered on, disconnect it for 20 seconds (power-cycle) before each pairing attempt.
2. Power on the device.
3. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
4. Push and hold the pairing button for 5 seconds; the LED light will start blinking upon release.
5. Return to the pairing page, provide a name for your device, and assign it to a room.
6. You’re all set! Enjoy using your Aqara Dual Relay Module T2.

Gewiss 2-channel Contact Interface (GWA1501)

Parameter	Details
Product Image
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Gewiss_GWA1501.groovy
Tested firmwares	1994-0002-00000400
Since version	5.1.0

Features

• Switch Style Configuration: This feature allows users to configure the physical switch style, with options including rocker / toggle, and push button.
• Button Events: Supports “Push” events for both buttons.
• Battery Report: Provides a percentage-based report on the current battery level.
• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.
• Contact Sensor: If enabled in Preferences panel, track open/closed state using two Contact Sensor child devices.

Pairing Instructions

1. Remove the battery. Replace with a fresh battery if the case.
2. Flip the switches in the off position (contacts I1/C1 and I2/C2 are open).
3. Set jumpers in position 0000 (▄ ▄ ▄ ▄) = Factory default.
4. Re-insert the battery.
5. Push and hold the small pairing button (A2 in manual) for at least 10 seconds. The status LED will flash red and green alternately for 3 seconds, then become red fixed. Device is now factory reset.
6. Remove the battery.
7. Set jumpers in position 1011 (▀ ▄ ▀ ▀) = Pairing configuration.
8. Re-insert the battery.
9. Device is now in pairing mode for 5 minutes. LED light should stay red.
10. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
11. LED should start to slowly blink green for a few seconds, then bink orange while driver is configuring the device.
12. After pairing is complete, the LED will continue to slowly blink green for a few minutes.
13. Provide a name for your device, and assign it to a room.
14. Set jumpers in position 0011 (▄ ▄ ▀ ▀) = One-way switch (on/off) configuration.
15. Flip switches on and off.
16. You’re all set! Enjoy using your Gewiss 2-channel Contact Interface.

Legrand Connected Outlet (741811)

Parameter	Details
Product Image
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Legrand_741811.groovy
Tested firmwares	003e
Since version	4.0.0

Features

• Command Controls: Includes “On”, “Off”, “Toggle”, and “On with Timed Off” commands.
• Power Outage Configuration: Configures the state after a power outage (options include “Power On”, “Power Off”, and “Restore previous state”).
• Power Reporting: Reports the power (in Watts)
• LED Mode: Configures the LED to be always on, always off, or to follow the device’s power state.
• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.
• Device State Refresh: Refreshes the device state on demand for real-time status updates.

Pairing Instructions

1. Find the small reset hole under the device face plate and make sure you have at hand a pin that can fit the reset hole (e.g.: a paper clip or SIM card eject pin).
2. If the device is already powered on, disconnect it for 20 seconds (power-cycle) before each pairing attempt.
3. Power on the device.
4. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
5. Insert the pin into the reset hole and press it for at least 5 seconds; upon release, the LED light will start blinking.
6. Return to the pairing page, provide a name for your device, and assign it to a room.
7. You’re all set! Enjoy using your Legrand Connected Outlet.

Philips Hue Wall Switch Module (RDM001)

Parameter	Details
Product Image
Product Link	Single｜2-Pack
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Philips_RDM001.groovy
Since version	4.0.0

Features

• Switch Style Configuration: This feature allows users to configure the switch style, with options including single rocker, single push button, dual rocker, and dual push button.
• Button Push Event: This feature supports events triggered by the push of either switch.
• Battery Report: Provides a percentage-based report on the current battery level.
• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.
• Zigbee Device Control: Enables direct control of On/Off settings for Zigbee devices.
• Direct Zigbee Group Control: Enables direct control of On/Off settings for Zigbee groups. This allows for efficient management of multiple devices.

Pairing Instructions

1. Connect the S1 switch cable
2. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
3. Press the reset button for 10 seconds.
4. When the LED starts blinking, close and release the S1 switch.
5. Return to the pairing page, provide a name for your device, and assign it to a room.
6. You’re all set! Enjoy using your Philips Hue Wall Switch Module.

Philips Hue Dimmer Switch (RWL022)

Parameter	Details
Product Image
Product Link	Philips Hue Dimmer Switch
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Philips_RWL022.groovy
Since version	4.0.0

Features

• Button Events: Supports “Push”, “Hold”, and “Release” events for all 4 buttons.
• Battery Report: Provides a percentage-based report on the current battery level.
• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.
• Zigbee Device Control: Enables direct control of On/Off settings for Zigbee devices.
• Direct Zigbee Group Control: Enables direct control of On/Off settings for Zigbee groups. This allows for efficient management of multiple devices.

Pairing Instructions

1. Open the battery compartiment, find the small reset hole and make sure you have at hand a pin that can fit the reset hole (e.g.: a paper clip or SIM card eject pin).
2. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
3. Insert the pin into the reset hole and press it for at least 5 seconds; upon release, the LED light on the first button will start blinking.
4. Return to the pairing page, provide a name for your device, and assign it to a room.
5. You’re all set! Enjoy using your Philips Hue Dimmer Switch.

Schneider Wiser UFH (CCTFR6600)

This device is extremely chatty as it polls the Hubitat hub for the status of each of the 6 zones every 1 minute. If no reponse is received from the hub for 10 minutes (10 failed polls), the device enters a “lost-connection” mode and turns all 6 zones to “On”.

Warning: The driver code for this device is still a work-in-progess.

Parameter	Details
Product Image
Product Link	Wiser Underfloor Heating Connection Strip
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Schneider_CCTFR6600.groovy
Since version	5.0.0

Features

• Command Controls: Includes “On” and “Off” for each of the 6 zones.
• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.

Pairing Instructions

1. In the Hubitat interface, navigate to Devices, click Add Device in the top right corner, select Zigbee, and then click Start Zigbee Pairing.
2. Press the connect button for at least 5 seconds; upon release, the LED light on the first button will start blinking green.
3. Return to the pairing page, provide a name for your device, and assign it to a room.
4. You’re all set! Enjoy using your Schneider Wiser UFH.

Swann One Key Fob (SWO-KEF1PA)

Parameter	Details
Product Image
Product Link	Swann One Key Fob
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Swann_SWO-KEF1PA.groovy
Since version	4.0.0

I don’t own this device and did not test it myself.

Features

• Button Events: Supports “Push” events for all 4 buttons.
• Battery Report: Provides a percentage-based report on the current battery level.
• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.

Known Issues

• Device drops off the Zigbee mesh (unknown reason)

Pairing Instructions

Unknown

Tuya Temperature and Humidity Sensor (TS0201)

Parameter	Details
Product Image
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Tuya_TS0201.groovy
Since version	5.0.0

Features

• Temperature and Humidity Measurements: Provide standard measurements of the current temperature and the amount of moisture in the air.
• Battery Report: Provides a percentage-based report on the current battery level.
• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.

Xiaomi Mi Temperature and Humidity Monitor 2 (LYWSD03MMC)

Converted from Bluetooth to Zigbee using this Zigbee 3.0 Firmware directly from the web browser (no wire soldering required).

Parameter	Details
Product Image
Product Link	Mi Temperature And Humidity Monitor 2
Manual install file	https://raw.githubusercontent.com/dan-danache/hubitat/master/ikea-zigbee-drivers/Xiaomi_LYWSD03MMC.groovy
Since version	5.1.0

Features

• Temperature and Humidity Measurements: Provide standard measurements of the current temperature and the amount of moisture in the air.
• Battery Report: Provides a percentage-based report on the current battery level.
• Health Status: Indicates the operational status of the device, showing whether it’s “online” or “offline”.

---

This site is open source. Improve this page.